STATE STANDARD OF THE USSR UNION

By Decree of the USSR State Committee on Standards of October 20, 1981 No. 4629, the introduction date was set

01.01.83

The validity period was lifted according to the protocol of the Interstate Council for Standardization, Metrology and Certification (IUS 2-93)

This standard applies to electric-welded pipes made of corrosion-resistant (stainless) steels intended for the manufacture of pipelines and various structures.

1. ASSORTMENT

1.1. The dimensions of the pipes must correspond to those indicated in the table. .

Table 1

(Changed edition, Amendment No. 2).

At the request of the consumer, pipes of size 38´ 1.5 and 43 ´ 1.5 mm are manufactured with maximum deviations in outer diameter mm.

1.1 - 1.4.

1.5. Ovality and variation in wall thickness of pipes should not take the pipe dimensions beyond the maximum deviations in diameter and wall thickness, respectively.

1.6. The tolerance for straightness of pipes should not exceed 1.5 mm per 1 m of length.

Examples of symbols

Pipe, outer diameter 25 mm and wall thickness 2 mm, of unmeasured length, made of steel grade 08Х18Н10Т:

Pipe 25 ´ 2 - 08Х18Н10Т GOST 11068-81

The same, with a length multiple of 2000 mm:

Pipe 25 ´ 2 ´ 2000 kr - 08Х18Н10Т GOST 11068-81

The same, measured length 6000 mm:

Pipe 25 ´ 2 ´ 6000 - 08Х18Н10Т GOST 11068-81

The same, with increased manufacturing precision:

Pipe 25P ´ 2P´ 6000 - 08Х18Н10Т GOST 11068-81

For heat-treated pipes, the letter T is placed after the word pipe.

2. TECHNICAL REQUIREMENTS

2.1. Pipes are manufactured in accordance with the requirements of this standard according to technological regulations approved in the prescribed manner, from steel grades 10Х18Н10Т and 04Х17Т with the chemical composition specified in table. , and steel grades 08Х18Н10Т, 08Х18Т1, 08 X 18H 10, 12Х18Н10Т, 10Х17Н13М2Т, 10Х17Н13М3Т, 08Х22Н6Т, 08Х21Н6М2Т, 06ХН28МДТ, 08Х17Н13М2Т, 03Х17Н14М3, 03Х18Н10Т with chemical composition according to GOST 5632-72.

Table 3

2.2 Pipes made from steel grades 08Х18Н10Т, 08Х18Т1, 10Х18Н10Т, 12Х18Н10Т, 04Х17Т are produced by heat-treated mechanical properties, indicated in table. 226 (23)

2.1, 2.2 (New edition, Amendment No. 2).

2.2.2. By agreement with the consumer, pipes can be subjected to cold and warm deformation in the mill line.

(Introduced additionally, Amendment No. 2).

2.3. Lack of penetration, pores, cracks, films, flaws, scale, and traces of over-etching are not allowed on the surface of the pipes.

Scratches, traces of straightening, scratches, traces of cleaning defects are allowed, if the thickness of the pipe wall does not exceed the maximum deviations, as well as tarnished colors formed as a result of heat treatment or welding.

By agreement with the consumer, it is possible to supply pipes made of steels 08Х18Т1 and 04Х17Т with an oxide film on the surface formed as a result of heat treatment.

Pipes can be produced with a polished outer surface. Roughness is established by agreement with the consumer.

On the outer surface of the pipes in places where they come into contact with the gasket, unetched areas are allowed due to the etching technology.

(New edition, Amendment No. 2).

2.4. The height of the internal flashing should not exceed:

0.7 mm - for general purpose pipes;

0.1 mm - for pipes used for the production of tubular heating elements.

At the request of the consumer pipes general purpose with a nominal internal diameter of over 20 mm, they are manufactured with a burr height of no more than 0.3 mm. The transition from the burr to the pipe walls should be smooth.

2.5. The ends of the pipes must be cut at right angles and cleared of burrs. Formation of a chamfer is allowed when removing burrs. At the request of the consumer, it is allowed to manufacture pipes with deburring and internal chamfering from one end, provided that the stripped ends are oriented in one direction.

At the customer's request, pipes are manufactured cut in line.

(New edition, Amendment No. 2).

2.6. For chemical engineering, the chemical industry, and at the request of the consumer for other industries, heat-treated pipes of their steel grades 08Х18Н10Т, 10Х18Н10Т, 10Х17Н13М2Т, 10Х17Н13М3Т, 08Х22Н6Т, 08Х21Н6М2Т, 06ХН28МДТ must withstand the intercrystal test Stallite corrosion.

2.7. Pipes made of steel grades 08Х18Н10Т, 10Х18Н10Т must withstand the flattening test up to a distance ( N) between flattening planes in millimeters, calculated by the formula

Where S n - nominal pipe wall thickness, mm;

D n - nominal outer diameter of the pipe, mm.

At customer's request for pipes with ratioS n/ D n , equal to 0.04 or more, distance N should not be more than 1/3D n.

Heat-treated pipes made of other steel grades must withstand the flattening test to a distance N, equal to 1/2 of the outer diameter.

Pipes without heat treatment must withstand the flattening test to a distance N, equal to 2/3 of the outer diameter.

(New edition, Amendment No. 2).

2.8. At the request of the consumer, heat-treated pipes must withstand the following tests:

expansion tests before increasing the outer diameter:

by 12% - for pipes of steel grades 08Х18Н10Т, 08Х18Т1, 08Х18Н10, 12Х18Н10Т, 10Х18Н10Т, 04Х17Т, 03Х18Н10Т, 08Х17Н13М2Т, 03Х17Н14М3;

by 6% - for pipes made of other steel grades.

By agreement of the parties, pipes made of steel grades 08Х18Т1, 10Х18Н10Т, 12Х18Н10Т must withstand the expansion test by 15%;

bead test until the width of the bent bead, measured from the inner surface of the pipe, is equal to 1.5 times the wall thickness (bead test is carried out on pipes with a diameter of at least 25 mm; bead angle 90° );

bend test (the bend radius is established by agreement between the manufacturer and the consumer).

(New edition, Amendment No. 2).

2.9. At the consumer's request, the metal grain size of finished pipes made of steel grades 10Х18Н10Т and 12Х18Н10Т should be 3 - 7 points.

2.10. Pipes must withstand test hydraulic pressure of 6 MPa (60 kgf/cm2) or continuity control weld non-destructive methods.

At the request of the consumer, pipes must withstand hydraulic pressure ( R 1) in accordance with the requirements of GOST 3845-75, but not more than 20 MPa (200 kgf/cm2). In this case, the permissible stress in the pipe wall is taken equal to 40% of the temporary tensile strength.

3. ACCEPTANCE RULES

3.1. Pipes are accepted in batches. The batch must consist of pipes of the same size in diameter and wall thickness, the same grade of steel, the same type of heat treatment and be accompanied by one quality document in accordance with GOST 10692-80.

The number of pipes in a batch should be no more than:

500 pcs. - with a diameter of up to 30 mm;

300 pcs. - with a diameter over 30 mm.

3.2. The chemical composition of steel is taken according to the document on the quality of the original coiled steel. If there is a disagreement in the assessment of the chemical composition, one pipe from the batch is selected for testing.

3.3. Each batch of pipes is subjected to checking the surface quality and dimensions, as well as testing the pipes with hydraulic pressure or non-destructive methods.

At the request of the consumer, when monitoring the welded seam of pipes using non-destructive methods, an additional hydraulic pressure test is carried out on 10 to 100% of the pipes in the batch.

(Changed edition, Amendment No. 1).

3.4. To check the height of the internal flash, 2% of the pipes from the batch are selected.

3.5. For tensile testing, intergranular corrosion, expansion, beading, bending, and flattening, two pipes from the batch are selected. To determine the grain size, one tube from the batch is selected.

The determination of the yield strength of the metal is carried out at the request of the consumer.

3.6. If unsatisfactory test results are obtained for at least one of the indicators, repeated tests are carried out on a double number of pipes selected from the same batch.

The results of repeated tests apply to the entire batch.

4. TEST METHODS

4.1. One sample is cut from each selected pipe for each type of test.

4.2. Chemical analysis is carried out according to GOST 12344-88, GOST 12346-78, GOST 12347-77, GOST 12348-78, GOST 12349-83, GOST 12350-78, GOST 12351-81, GOST 12352-81, GOST 12353-78, GOST 12354-81, GOST 12355-78, GOST 12356-81, GOST 12365-84 or GOST 28473-90,

wall thickness, thickness difference and internal burr height - with a micrometer according to GOST 6507-90 or a wall gauge according to GOST 11358-89. The height of the internal flash is measured at a distance of up to 25 mm from the ends of the pipes, and the outer diameter is measured at least 15 mm from the ends of the pipes.

Length can be controlled outside diameter and pipe wall thickness by automatic means according to regulatory documentation. In case of disagreement in the assessment of measurement results, control is carried out using the measuring instruments given above.

(Changed edition, Amendment No. 1, 2).

4.5. The grain size is determined by the base metal according to GOST 5639-82. In this case, the pipes are not tested for intergranular corrosion.

4.6. Sampling and testing for intergranular corrosion are carried out in accordance with GOST 6032-89. In case of disagreement in assessing the results, tests are carried out according to the method A.M. GOST 6032-89, except for pipes made of steel grade 06ХН28МДТ.

(Changed edition, Amendment No. 1).

4.7. The tensile test is carried out according to GOST 10006-80 on a short longitudinal sample (in the form of a strip with a seam or a piece of pipe). The test speed up to the yield point should be no more than 10 mm/min, beyond the yield point - no more than 40 mm/min.

4.8. Hydraulic testing is carried out in accordance with GOST 3845-75 with holding pressure for at least 5 s.

4.9. The expansion test is carried out according to GOST 8694-75 on a mandrel with a taper of 30°.

4.10. The boarding test is carried out according to GOST 8693-80.

4.11. The flattening test is carried out according to GOST 8695-75 with the weld positioned horizontally. At the request of the consumer, the test should be carried out in two positions of the weld seam: horizontally and vertically.

(Changed edition, Amendment No. 2).

4.12. The bending test is carried out according to GOST 3728-78.

4.13. Non-destructive quality control of the weld is carried out according to regulatory documentation.

4.14. The right angle for cutting pipe ends is not controlled and is determined by the design of the pipe cutting equipment.

(Introduced additionally, Amendment No. 1).

5. LABELING, PACKAGING, TRANSPORTATION AND STORAGE

5.1. Labeling, packaging, transportation and storage - in accordance with GOST 10692-80.

(Changed edition, Amendment No. 1).

5.2. (Deleted, Amendment No. 2).

page 1

page 2

page 3

page 4

page 5

page 6

page 7

page 8

page 9

INTERSTATE STANDARD

ELECTRIC WELDED PIPES FROM
CORROSION-RESISTANT STEEL

Specifications

IPC PUBLISHING HOUSE OF STANDARDS

Moscow

INTERSTATE STANDARD

By Decree of the USSR State Committee on Standards dated October 20, 1981 No. 4629, the implementation date was set as 01/01/83

The validity period was lifted according to the protocol of the Interstate Council for Standardization, Metrology and Certification (IUS 2-93)

This standard applies to electric-welded pipes made of corrosion-resistant (stainless) steels intended for the manufacture of pipelines and various structures.

(Changed edition, Amendment No. 2).

1. ASSORTMENT

1.1. The dimensions of the pipes must correspond to those indicated in the table. 1.

Table 1

Notes:

1. Pipe sizes taken in brackets are not recommended when designing new facilities.

2. Theoretical mass of 1 m of pipes ( T), kg, calculated by the formula

Where D n - nominal outer diameter of the pipe, mm;

s n - nominal pipe wall thickness, mm;

γ - metal density, g/cm 3, depending on the steel grade:

08Х18Н10Т, 10Х18Н10Т, 12Х18Н10Т, 03Х18Н10Т, 08Х18Н10 - 7.9;

08Х21Н6М2Т - 7.85;

10Х17Н13М2Т, 10Х17Н13М3Т, 03Х17Н13М2Т, 03Х17Н14М3 - 8.0;

06ХН28МДТ - 7.95;

04X17T, 08X18T1 - 7.72.

3. Pipes from steel grades 08Х18Т1 and 04Х17Т are manufactured with a wall thickness of up to 2.0 mm.

4. By agreement between the manufacturer and the consumer, pipes can be manufactured: of intermediate sizes with tolerances for the diameter and wall thickness of adjacent large sizes; from corrosion-resistant steels of the best grades; with mixed or one-sided tolerance on the outer diameter. The size of the offset or one-sided tolerance field should not exceed the sum of two-sided deviations.

(Changed edition, Amendment No. 2).

1.2. According to the length of the pipe, the following should be made:

measured length - from 5 to 9 m;

measured length with the remainder - no more than 10% (by weight) of pipes of unmeasured length;

multiple measured length - up to 9 mm with an allowance for each cut of 5 mm (unless another allowance is specified in the order), which is included in each multiple length;

multiple lengths with a remainder of no more than 10% (by weight) of pipes of unmeasured length;

unmeasured length - from 1.5 to 9 m.

1.3. Maximum deviations along the length of pipes of measured and multiple lengths should not exceed +15 mm.

1.2, 1.3 (Changed edition, Amendment No. 1).

1.4. The maximum deviations for the outer diameter and wall thickness are indicated in table. 2.

table 2

At the request of the consumer, pipes with dimensions of 38´1.5 and 43´1.5 mm are manufactured with maximum deviations in outer diameter mm.

1.4(Changed edition, Amendment No. 1, 2).

1.5. Ovality and variation in wall thickness of pipes should not take the pipe dimensions beyond the maximum deviations in diameter and wall thickness, respectively.

1.6. The tolerance for straightness of pipes should not exceed 1.5 mm per 1 m of length.

Examples of symbols

Pipe, outer diameter 25 mm and wall thickness 2 mm, of unmeasured length, made of steel grade 08Х18Н10Т:

Pipe 25 ´2 - 08Х18Н10Т GOST 11068-81

The same, with a length multiple of 2000 mm:

Pipe 25 ´2´2000 kr - 08Х18Н10Т GOST 11068-81

The same, measured length 6000 mm:

Pipe 25 ´2´6000 - 08Х18Н10Т GOST 11068-81

The same, with increased manufacturing precision:

Pipe 25P´2П´6000 - 08Х18Н10Т GOST 11068-81

For heat-treated pipes, the letter T is placed after the word pipe.

2. TECHNICAL REQUIREMENTS

2.1. Pipes are manufactured in accordance with the requirements of this standard according to technological regulations approved in the prescribed manner, from steel grades 10Х18Н10Т and 04Х17Т with the chemical composition specified in table. 3, and steel grades 08Х18Н10Т, 08Х18Т1, 08Х18H10, 12Х18Н10Т, 10Х17Н13М2Т, 10Х17Н13М3Т, 08Х22Н6Т, 08Х21Н6М2Т, 06ХН28МДТ, 08Х17Н13М2Т, 03Х 17N14M3, 03Х18Н10Т with chemical composition in accordance with GOST 5632-72.

Table 3

2.2 Pipes made from steel grades 08Х18Н10Т, 08Х18Т1, 10Х18Н10Т, 12Х18Н10Т, 04Х17Т are manufactured by heat treatment with mechanical properties specified in table. 4. The mechanical properties of pipes made of steel 08Х18Т1 and 04Х17Т for wall thicknesses of more than 1.5 mm are established by agreement of the parties.

Table 4

2.1, 2.2 (Changed edition, Amendment No. 2).

2.2.1. Pipes from other grades of steel specified in clause 2.1 are manufactured heat-treated, and at the request of the consumer, without heat treatment; in this case, the mechanical properties are established by agreement between the manufacturer and the consumer.

The number of pipes in a batch should be no more than:

500 pcs. - with a diameter of up to 30 mm;

300 pcs. - with a diameter over 30 mm.

3.2. The chemical composition of steel is taken according to the document on the quality of the original coiled steel. If there is a disagreement in the assessment of the chemical composition, one pipe from the batch is selected for testing.

3.3. Each batch of pipes is subjected to checking the surface quality and dimensions, as well as testing the pipes with hydraulic pressure or non-destructive methods.

At the request of the consumer, when monitoring the welded seam of pipes using non-destructive methods, an additional hydraulic pressure test is carried out on 10 to 100% of the pipes in the batch.

3.4. To check the height of the internal flash, 2% of the pipes from the batch are selected.

3.5. For tensile testing, intergranular corrosion, expansion, beading, bending, and flattening, two pipes from the batch are selected. To determine the grain size, one tube from the batch is selected.

The determination of the yield strength of the metal is carried out at the request of the consumer.

3.6. If unsatisfactory test results are obtained for at least one of the indicators, repeated tests are carried out on a double number of pipes selected from the same batch.

The results of repeated tests apply to the entire batch.

4. TEST METHODS

4.1. One sample is cut from each selected pipe for each type of test.

4.2. Chemical analysis is carried out according to GOST 12344-88, GOST 12346-78, GOST 12347-77, GOST 12348-78, or, or with a micrometer according to GOST 6507-90;

deviation from straightness - with a straight edge in accordance with GOST 8026-92 and a feeler gauge in accordance with the regulatory document;

wall thickness, thickness difference and internal burr height - with a micrometer according to GOST 6507-90 or a wall gauge according to GOST 11358-89. The height of the internal flash is measured at a distance of up to 25 mm from the ends of the pipes, and the outer diameter is measured at least 15 mm from the ends of the pipes.

It is allowed to control the length, outer diameter and wall thickness of pipes by automatic means according to regulatory documentation. In case of disagreement in the assessment of measurement results, control is carried out using the measuring instruments given above.

On a short longitudinal sample (in the form of a strip with a seam or a piece of pipe). The test speed up to the yield point should be no more than 10 mm/min, beyond the yield point - no more than 40 mm/min.

4.13. Non-destructive quality control of the weld is carried out according to regulatory documentation.

4.14. The right angle for cutting pipe ends is not controlled and is determined by the design of the pipe cutting equipment.

(Introduced additionally, Amendment No. 1).

5. LABELING, PACKAGING, TRANSPORTATION AND STORAGE

5.1. Labeling, packaging, transportation and storage - in accordance with GOST 10692-80.

(Changed edition, Amendment No. 1).

5.2 (Deleted, Amendment No. 2).

Change No. 2 was adopted by the Interstate Council for Standardization, Metrology and Certification (Minutes No. 10 of 03.10.96)

GOST 11068-81 spreads on electric welded pipes made of corrosion-resistant (stainless) steels, intended for the manufacture of pipelines and various structures.

• GOST 2216-84 Smooth adjustable clamp gauges. Specifications
• GOST 3728-78 Pipes. Bend test method
• GOST 3845-75 Metal pipes. Hydraulic pressure test method
• GOST 5632-72 High-alloy steels and corrosion-resistant, heat-resistant and heat-resistant alloys. Stamps
• GOST 5639-82 Steels and alloys. Methods for identifying and determining grain size
• GOST 6032-89 Corrosion-resistant steels and alloys. Test methods for resistance to intergranular corrosion
• GOST 6507-90 Micrometers. Specifications
• GOST 7502-89 Metal measuring tapes. Specifications
• GOST 7565-81 Cast iron, steel and alloys. Sampling method for determining chemical composition
• GOST 8026-92 Calibration rulers. Specifications
• GOST 8693-80 Metal pipes. Board test method
• GOST 8694-75 Pipes. Dispense test method
• GOST 8695-75 Pipes. Flattening test method
• GOST 10006-80 Metal pipes. Tensile test method
• GOST 10692-80 Steel, cast iron pipes and connecting parts for them. Reception, labeling, packaging, transportation and storage
• GOST 11358-89 Indicator thickness and wall gauges with division values ​​of 0.01 and 0.1 mm. Specifications
• GOST 12344-88 Alloy and high-alloy steels. Carbon determination methods
• GOST 12346-78 Alloy and high-alloy steels. Methods for determining silicon
• GOST 12347-77 Alloy and high-alloy steels. Phosphorus determination methods
• GOST 12348-78 Alloy and high-alloy steels. Methods for determining manganese
• GOST 12349-83 Alloy and high-alloy steels. Methods for determining tungsten
• GOST 12350-78 Alloy and high-alloy steels. Methods for determining chromium
• GOST 12351-81 Alloy and high-alloy steels. Methods for determining vanadium
• GOST 12352-81 Alloy and high-alloy steels. Methods for determining nickel
• GOST 12353-78 Alloy and high-alloy steels. Methods for determining cobalt
• GOST 12354-81 Alloy and high-alloy steels. Methods for determining molybdenum
• GOST 12355-78 Alloy and high-alloy steels. Methods for determining copper
• GOST 12356-81 Alloy and high-alloy steels. Methods for determining titanium
• GOST 12365-84 Alloy and high-alloy steels. Methods for determining zirconium
• GOST 28473-90 Cast iron, steel, ferroalloys, chrome, manganese metal. General requirements to methods of analysis
• GOST 22536.0-87 Carbon steel and unalloyed cast iron. General requirements for analysis methods
• GOST 22536.14-88 Carbon steel and unalloyed cast iron. Method for determination of zirconium

• 10.26.2019 at 12:15 Enterprise Mikron-Marin LLC will acquire:
  Stainless steel pipes, seamless Ø345x30(32); Ø351x30(32); Ø377x40(45),(48)
  Stainless steel pipes, electric welded Ø345x30(32); Ø351x30(32); Ø377x40(45),(48) length: 1110 steel: St. 20Х13,30Х13, (analogues) according to GOST, TU, in the following volume: 1 piece
  

  Customer's wishes: Can you help with the supply of stainless steel? pipes St. 20Х13,30Х13, (analogues) according to GOST, TU…. standard sizes: Ø345x30(32); Ø351x30(32); Ø377x40(45),(48)…. Clean size Ø340xØ300x1110 details. -1 PC. Thank you in advance for your prompt response. respond to the request

• 10.23.2019 at 13:30 Enterprise Spetsstal LLC will acquire:
  Stainless steel pipes, electric welded 273x5-8
  Stainless steel pipes, seamless 273x5-8 length: 1.7 steel: AISI310S, in the following volume: 1 piece
  respond to the request
• 10/22/2019 at 12:20 Organization (contact person: Alexander) wishes to purchase:
  Stainless steel pipes, electric welded 19.05x1.65 steel: EN 1.4404, in the following volume: 30 m/p
  

  Additions from the customer: We need pipes NS 19.05x1.65 EN 1.4404 (AISI 316L) MP 30 respond to the request

• 10.22.2019 at 10:51 Enterprise LLC "REGINZHSTROY" wishes to purchase:
  Stainless steel pipes, electric welded D=160x2.0 mm in the following volume: 15 m/p
  

  Additions from the customer: You need a ventilation pipe D=160x2.0 mm length L=15.0 m.p made of stainless steel pcs 1 respond to the request

• 10.21.2019 at 14:34 Organization (contact person: Evgeniya) wishes to purchase:
  length: L=300mm steel: B-20 GOST 8733-74 GOST 8734-75, in the following volume: 3 pcs Steel sheet, cold rolled 32x4 length: L=100mm steel: B-20 GOST 8733-74 GOST 8734-75, in the following volume: 8 m2 Steel sheet, cold rolled 32x3.5 length: L=100mm steel: B-20 GOST 8733-74 GOST 8734-75, in the following volume: 1 piece Steel sheet, cold rolled 25x3.5 length: L=80mm steel: B-20 GOST 8733-74 GOST 8734-75, in the following volume: 4 pcs Steel sheet, cold rolled 14x3 length: L=50mm steel: B-20 GOST 8733-74 GOST 8734-75, in the following volume: 3 pcs length: L=100mm steel: AISI316L, in the following volume: 3 pcs Stainless steel pipes, electric welded 33.7x2 length: L=100mm steel: AISI 304L, in the following volume: 2 pcs

  Additions from the customer: Cold-deformed seamless steel pipes with external cylindrical pipe thread, 32x4 L=300mm V-20 GOST 8733-74 pcs 3 Cold-deformed seamless steel pipes with external cylindrical pipe threads, 32x4 L=100mm V-20 GOST 8733-74 pcs 8 Cold-deformed seamless steel pipes with external cylindrical pipe thread, 32x3.5 L=100mm V-20 GOST 8733-74 pcs 1 Seamless cold-deformed steel pipes with external cylindrical pipe thread, 25x3.5 L=80mm V-20 GOST 8733-74 pcs 4 Seamless cold-deformed steel pipes with external pipe cylindrical thread, 14x3 L=50mm V-20 GOST 8733-74 pcs 3 Pipes ES 33.7x2 L=100mm AISI316L pcs 3 Pipes ES 33.7x2 L=100mm AISI 304L pcs 2 respond to the request

Advertisements sell buy Stainless steel pipes, electric welded GOST 11068-81 in the Moscow region

Stainless steel pipes 219x6 10t 330tr/t. 12Х18Н10Т.
Stainless steel pipes 76x3 12Х18Н10Т 220 tr/t. Stainless steel pipes 219x6 12Х18Н10Т 10t 330tr/t. Seamless pipes 168x4, 5 12Х18Н10Т. Seamless pipes 100x3 12X18N10T for 390 RUR/kg. Pipes 273-550mm 15Х5М and 15ХМ. From 98r/kg including VAT. Seamless pipes 25x2x4100mm 12X18N10T. Seamless pipes 2x0, 2...

220rub!!! Stainless steel pipes 76x3 12Х18Н10Т 220 tr/t.
Stainless steel pipes 219x6 12Х18Н10Т 10t 330tr/t. Seamless pipes 168x4.5 12Х18Н10Т Seamless pipes 100х3 12Х18Н10Т 390 RUR/kg. Pipes 273-550mm 15Х5М and 15ХМ. From 98r/kg including VAT. Seamless pipes 25x2x4000mm 12X18N10T. Seamless pipes 2x0.2, 3x0.3, 4x0.8, 5x0.5, 6x0.5, 6x1, 6x1.5 -08Х18Н10Т. ...

I sell Stainless Seam Pipes of Soviet production.
I sell Stainless Seam Pipes of Soviet production. Price for the entire volume: cash payment 150 rub./kg, non-cash payment 180 rub./kg tel. cell: +7-910-136-91-20, +7-996-003-75-63 , +79159324523 08(12)Х18Н10Т Diameter/wall thickness/length 63x1.5mm - 5.4m weight 1890kg ~20% wrinkled . 76...

I sell Pipes 12(08)Х18Н10Т, Aisi 304, 1.4466, Х17Н13М2Т, 20Х23Н18, 10Х17Н13М2Т, price from 150 rub./kg.
I sell Pipes 12(08)Х18Н10Т, Aisi 304, 1.4466, Х17Н13М2Т, 20Х23Н18, 10Х17Н13М2Т, price from 150 rub./kg. Price on request. tel. +7-910-136-91-20, +7-996-003-75-63, +79159324523 email. mail: [email protected] Pipe Brand diameter/thickness length, mm 08(12)Х18Н10Т 9.5х1.1 ...

Request for AISI 304 products
I propose to consider the possibility and inform you of the terms of delivery of stainless steel products: No. Name Quantity Units. change 1.1. Pipe 273.0x2.0-AISI 304(L) DIN 17457 200 m 1.2. Pipe 273.0x3.0-AISI 304(L) DIN 17457 200 m 2.1. Pipe 159.0x2.0-AISI 304(L) DIN 17457 200 m 2.2. Pipe 168.3x2.0-A...

I will buy stainless pipes


I will buy electric-welded longitudinally seam pipes
I will buy pipes (new, old, from the state reserve) stainless steel electric-welded straight-seam steel 08Х18Н10Т; 12Х18Н10Т; 03Х17Н14М3; 08Х18Н10; 03Х18Н10;

We will buy pipes 720x16 12X18N10T.
We will buy pipes 720x16 12X18N10T. Let's buy seamless pipes 32x3 12Х18Н10Т. We will buy seamless pipes 76x4 12Х18Н10Т. We will buy seamless pipes 32x6 12Х18Н10Т. 8-900-02-72-888. We will buy stainless steel sheets 8mm 1.5x6m 10Х17Н13М2Т (aisi 316Ti). Stock balance. Unliquid assets. 8-900-088-88-86. Yuri Nikolaevich. We will buy seamless...

Stainless steel pipe-=-=st..08x13, f25x2x6000mm---GOST 9941-81 - 1962 meters
Buy Stainless steel pipe-=-=st..08x13, diameter 25x2x6000mm --- GOST 9941-81 - 1962 meters

STATE STANDARD OF THE USSR UNION

By Decree of the USSR State Committee on Standards of October 20, 1981 No. 4629, the introduction date was set

01.01.83

The validity period was lifted according to the protocol of the Interstate Council for Standardization, Metrology and Certification (IUS 2-93)

This standard applies to electric-welded pipes made of corrosion-resistant (stainless) steels intended for the manufacture of pipelines and various structures.

1. ASSORTMENT

1.1. The dimensions of the pipes must correspond to those indicated in the table. .

Table 1

(Changed edition, Amendment No. 2).

At the request of the consumer, pipes of size 38´ 1.5 and 43 ´ 1.5 mm are manufactured with maximum deviations in outer diameter mm.

1.1 - 1.4.

1.5. Ovality and variation in wall thickness of pipes should not take the pipe dimensions beyond the maximum deviations in diameter and wall thickness, respectively.

1.6. The tolerance for straightness of pipes should not exceed 1.5 mm per 1 m of length.

Examples of symbols

Pipe, outer diameter 25 mm and wall thickness 2 mm, of unmeasured length, made of steel grade 08Х18Н10Т:

Pipe 25 ´ 2 - 08Х18Н10Т GOST 11068-81

The same, with a length multiple of 2000 mm:

Pipe 25 ´ 2 ´ 2000 kr - 08Х18Н10Т GOST 11068-81

The same, measured length 6000 mm:

Pipe 25 ´ 2 ´ 6000 - 08Х18Н10Т GOST 11068-81

The same, with increased manufacturing precision:

Pipe 25P ´ 2P´ 6000 - 08Х18Н10Т GOST 11068-81

For heat-treated pipes, the letter T is placed after the word pipe.

2. TECHNICAL REQUIREMENTS

2.1. Pipes are manufactured in accordance with the requirements of this standard according to technological regulations approved in the prescribed manner, from steel grades 10Х18Н10Т and 04Х17Т with the chemical composition specified in table. , and steel grades 08Х18Н10Т, 08Х18Т1, 08 X 18H 10, 12Х18Н10Т, 10Х17Н13М2Т, 10Х17Н13М3Т, 08Х22Н6Т, 08Х21Н6М2Т, 06ХН28МДТ, 08Х17Н13М2Т, 03Х17Н14М3, 03Х18Н10Т with chemical composition according to GOST 5632-72.

Table 3

2.2 Pipes made from steel grades 08Х18Н10Т, 08Х18Т1, 10Х18Н10Т, 12Х18Н10Т, 04Х17Т are manufactured by heat treatment with mechanical properties specified in table. 226 (23)

2.1, 2.2 (New edition, Amendment No. 2).

2.2.2. By agreement with the consumer, pipes can be subjected to cold and warm deformation in the mill line.

(Introduced additionally, Amendment No. 2).

2.3. Lack of penetration, pores, cracks, films, flaws, scale, and traces of over-etching are not allowed on the surface of the pipes.

Scratches, traces of straightening, scratches, traces of cleaning defects are allowed, if the thickness of the pipe wall does not exceed the maximum deviations, as well as tarnished colors formed as a result of heat treatment or welding.

By agreement with the consumer, it is possible to supply pipes made of steels 08Х18Т1 and 04Х17Т with an oxide film on the surface formed as a result of heat treatment.

Pipes can be produced with a polished outer surface. Roughness is established by agreement with the consumer.

On the outer surface of the pipes in places where they come into contact with the gasket, unetched areas are allowed due to the etching technology.

(New edition, Amendment No. 2).

2.4. The height of the internal flashing should not exceed:

0.7 mm - for general purpose pipes;

0.1 mm - for pipes used for the production of tubular heating elements.

At the request of the consumer, general purpose pipes with a nominal internal diameter of over 20 mm are manufactured with a burr height of no more than 0.3 mm. The transition from the burr to the pipe walls should be smooth.

2.5. The ends of the pipes must be cut at right angles and cleared of burrs. Formation of a chamfer is allowed when removing burrs. At the request of the consumer, it is allowed to manufacture pipes with deburring and internal chamfering from one end, provided that the stripped ends are oriented in one direction.

At the customer's request, pipes are manufactured cut in line.

(New edition, Amendment No. 2).

2.6. For chemical engineering, the chemical industry, and at the request of the consumer for other industries, heat-treated pipes of their steel grades 08Х18Н10Т, 10Х18Н10Т, 10Х17Н13М2Т, 10Х17Н13М3Т, 08Х22Н6Т, 08Х21Н6М2Т, 06ХН28МДТ must withstand the intercrystal test Stallite corrosion.

2.7. Pipes made of steel grades 08Х18Н10Т, 10Х18Н10Т must withstand the flattening test up to a distance ( N) between flattening planes in millimeters, calculated by the formula

Where S n - nominal pipe wall thickness, mm;

D n - nominal outer diameter of the pipe, mm.

At customer's request for pipes with ratioS n/ D n , equal to 0.04 or more, distance N should not be more than 1/3D n.

Heat-treated pipes made of other steel grades must withstand the flattening test to a distance N, equal to 1/2 of the outer diameter.

Pipes without heat treatment must withstand the flattening test to a distance N, equal to 2/3 of the outer diameter.

(New edition, Amendment No. 2).

2.8. At the request of the consumer, heat-treated pipes must withstand the following tests:

expansion tests before increasing the outer diameter:

by 12% - for pipes of steel grades 08Х18Н10Т, 08Х18Т1, 08Х18Н10, 12Х18Н10Т, 10Х18Н10Т, 04Х17Т, 03Х18Н10Т, 08Х17Н13М2Т, 03Х17Н14М3;

by 6% - for pipes made of other steel grades.

By agreement of the parties, pipes made of steel grades 08Х18Т1, 10Х18Н10Т, 12Х18Н10Т must withstand the expansion test by 15%;

bead test until the width of the bent bead, measured from the inner surface of the pipe, is equal to 1.5 times the wall thickness (bead test is carried out on pipes with a diameter of at least 25 mm; bead angle 90° );

bend test (the bend radius is established by agreement between the manufacturer and the consumer).

(New edition, Amendment No. 2).

2.9. At the consumer's request, the metal grain size of finished pipes made of steel grades 10Х18Н10Т and 12Х18Н10Т should be 3 - 7 points.

2.10. Pipes must withstand a test hydraulic pressure of 6 MPa (60 kgf/cm2) or control of the continuity of the weld using non-destructive methods.

At the request of the consumer, pipes must withstand hydraulic pressure ( R 1) in accordance with the requirements of GOST 3845-75, but not more than 20 MPa (200 kgf/cm2). In this case, the permissible stress in the pipe wall is taken equal to 40% of the temporary tensile strength.

3. ACCEPTANCE RULES

3.1. Pipes are accepted in batches. The batch must consist of pipes of the same size in diameter and wall thickness, the same grade of steel, the same type of heat treatment and be accompanied by one quality document in accordance with GOST 10692-80.

The number of pipes in a batch should be no more than:

500 pcs. - with a diameter of up to 30 mm;

300 pcs. - with a diameter over 30 mm.

3.2. The chemical composition of steel is taken according to the document on the quality of the original coiled steel. If there is a disagreement in the assessment of the chemical composition, one pipe from the batch is selected for testing.

3.3. Each batch of pipes is subjected to checking the surface quality and dimensions, as well as testing the pipes with hydraulic pressure or non-destructive methods.

At the request of the consumer, when monitoring the welded seam of pipes using non-destructive methods, an additional hydraulic pressure test is carried out on 10 to 100% of the pipes in the batch.

(Changed edition, Amendment No. 1).

3.4. To check the height of the internal flash, 2% of the pipes from the batch are selected.

3.5. For tensile testing, intergranular corrosion, expansion, beading, bending, and flattening, two pipes from the batch are selected. To determine the grain size, one tube from the batch is selected.

The determination of the yield strength of the metal is carried out at the request of the consumer.

3.6. If unsatisfactory test results are obtained for at least one of the indicators, repeated tests are carried out on a double number of pipes selected from the same batch.

The results of repeated tests apply to the entire batch.

4. TEST METHODS

4.1. One sample is cut from each selected pipe for each type of test.

4.2. Chemical analysis is carried out according to GOST 12344-88, GOST 12346-78, GOST 12347-77, GOST 12348-78, GOST 12349-83, GOST 12350-78, GOST 12351-81, GOST 12352-81, GOST 12353-78, GOST 12354-81, GOST 12355-78, GOST 12356-81, GOST 12365-84 or GOST 28473-90,

wall thickness, thickness difference and internal burr height - with a micrometer according to GOST 6507-90 or a wall gauge according to GOST 11358-89. The height of the internal flash is measured at a distance of up to 25 mm from the ends of the pipes, and the outer diameter is measured at least 15 mm from the ends of the pipes.

It is allowed to control the length, outer diameter and wall thickness of pipes by automatic means according to regulatory documentation. In case of disagreement in the assessment of measurement results, control is carried out using the measuring instruments given above.

(Changed edition, Amendment No. 1, 2).

4.5. The grain size is determined by the base metal according to GOST 5639-82. In this case, the pipes are not tested for intergranular corrosion.

4.6. Sampling and testing for intergranular corrosion are carried out in accordance with GOST 6032-89. In case of disagreement in assessing the results, tests are carried out according to the method A.M. GOST 6032-89, except for pipes made of steel grade 06ХН28МДТ.

(Changed edition, Amendment No. 1).

4.7. The tensile test is carried out according to GOST 10006-80 on a short longitudinal sample (in the form of a strip with a seam or a piece of pipe). The test speed up to the yield point should be no more than 10 mm/min, beyond the yield point - no more than 40 mm/min.

4.8. Hydraulic testing is carried out in accordance with GOST 3845-75 with holding pressure for at least 5 s.

4.9. The expansion test is carried out according to GOST 8694-75 on a mandrel with a taper of 30°.

4.10. The boarding test is carried out according to GOST 8693-80.

4.11. The flattening test is carried out according to GOST 8695-75 with the weld positioned horizontally. At the request of the consumer, the test should be carried out in two positions of the weld seam: horizontally and vertically.

(Changed edition, Amendment No. 2).

4.12. The bending test is carried out according to GOST 3728-78.

4.13. Non-destructive quality control of the weld is carried out according to regulatory documentation.

4.14. The right angle for cutting pipe ends is not controlled and is determined by the design of the pipe cutting equipment.

(Introduced additionally, Amendment No. 1).

5. LABELING, PACKAGING, TRANSPORTATION AND STORAGE

5.1. Labeling, packaging, transportation and storage - in accordance with GOST 10692-80.

(Changed edition, Amendment No. 1).

5.2. (Deleted, Amendment No. 2).

home » Investments » GOST 11068 81 stainless steel electric-welded pipes. Electric-welded pipes made of corrosion-resistant steel. Labeling, packaging, transportation and storage