Mesh feeders for grass for chickens. Do-it-yourself bunker feeder for chickens: how to make different designs. A simple option from a plastic bottle

If you are planning to have chickens and have already built a chicken coop for them, then it’s time to think about creating a chicken feeder with your own hands.

It is very easy to make a chicken feeder with your own hands, since to create it you can use the most various materials. Let's look at the most simple ways making chicken feeders with your own hands.

Where to start?

You can make your own chicken feeder make from anything. For this you can use boards, boxes, pipes and even plastic bottles.

However, regardless of the material chosen, a problem will arise - mixing the feed. If you make several feeders at once, they will take up a lot of space.

Despite this, there is still a way out of this situation, which will be discussed a little later.

Before you start making a chicken feeder with your own hands, you need to decide on the sizes And choosing a place, on which the future structure will stand. Regardless of whether the feeder will be in the chicken coop or on the street, there should be free access to it. Hens or chicks should not interfere with each other while feeding.

In addition, do not forget that chickens need not only dry, but also wet food. For the first case, bunker feeders for chickens in the form of a cylinder, in which feed is added automatically, can be perfect. Best used for wet food trough-shaped feeders, on top of which a turntable made of timber is installed.

Of course, the process of making a trough with your own hands is different from the process of making a bunker feeder. There is also a significant difference in labor costs.

However, modern equipment and materials greatly simplify the process, thanks to which difficulties will not arise.

Let's take a closer look at how you can make feeders for chickens or chickens with your own hands. from scrap materials.

DIY cutting board feeder

To make such unusual feeder for chickens you will need the following materials:

Cutting board;
Funnel;
Small plastic cup;
Rubber hose;
Electric drill.

To make a feeding device from a cutting board, follow these steps:

The outer contours of the funnel must be outlined on the board. Try to do everything as accurately as possible;
Inside the resulting drawn circle you need to drill many holes using a drill. At the same time, it is important not to overdo it so that the feed supply is limited;
Next, you need to take a pre-prepared transparent hose and connect it to the end of the funnel. If the hose does not sit tightly on the funnel, you can use additional fasteners, for example, a clamp;
Take a plastic cup and make a hole in the side at the very bottom with such a diameter that the end of the hose fits tightly into it and holds well in it;
Take the other end of the hose and insert it into the resulting hole. If the hose is not held tightly in the hole, then its edges and the outer surface of the hose must be treated with sealant;
After this, you need to glue the funnel bell to the board. It is necessary to treat the contour of the circle with sealant;
A funnel is placed on the circle and held in this position until the sealant is completely dry;
Connect one end of the hose to the bowl and the other to the funnel, which is glued to the board. The funnel should be at the bottom of the cutting board.

The chicken feeder is ready. You can add grain. It is worth paying attention to the fact that the board must be stable, since chickens or chickens will sit on it.

The bunker design can be considered automatic, since human participation when feeding chickens or hens will be minimal here.

Hopper feeder You can buy it ready-made in a store, but the cost will be rather high. You can also make the design yourself. The procedure for making a bunker feeder for chickens is very simple.

For manufacturing you will need the following materials:

Plastic bucket;
Sectional bowl for animals.

Step-by-step instructions for making a bunker feeder for chickens and hens:

In the lower part of the plastic bucket, make small holes along the entire diameter in the amount of 6-7 pieces (depending on the number of sections in the bowl), through which the food will pour out;
Attach a sectional bowl to the bottom of the plastic bucket using screws;
Fill a plastic bucket with chicken or chicken feed and close the lid.

The main advantage of such a bunker feeder is that it can be installed almost anywhere. The convenience of this design is that as food is consumed it will automatically flow into the bowl under the influence of its weight.

DIY plastic bottle feeder

Nowadays, water is often stored in plastic containers. Such containers can probably be found in every home and can be used to make chicken feeders with your own hands.

Step-by-step instructions for making a chicken or chicken feeder from plastic bottle:

Cut the plastic bottle in half. It is necessary to make vertical holes in the lower half of the bottle of such a size that a chicken head fits through it;
Take the second bottle and cut out the bottom in it, place the neck down inside the prepared cut. Thus, a few centimeters should remain between the neck and the bottom;
Pour grain or other food inside and cover the top of the bottle with something.

The only disadvantage of this design is that it will have to be moved indoors during bad weather, but such a feeder is ideal for a chicken coop.

For chickens, you can make the same feeder, but smaller. At the same time, the manufacturing technology will remain the same.

You can also make a chicken feeder yourself from ordinary boards. First you need to prepare the following materials:

Thick plywood or wood;
Electric drill, drills;
Loops, 2 pcs;
Sandpaper;
Saw;
Screwdriver;
Simple pencil;
Roulette.

First you need to create a drawing, which is then transferred to the tree. Dimensions of the required elements: bottom - 29x17 cm, sides - height 40 cm with a top edge of 20 cm and a bottom edge of 20 cm, front walls - 28x29 cm and 70x29 cm, top cover - 26x29 cm, back wall - 40x29 cm;
After all the elements are transferred to the boards, they must be carefully cut out;
In some places, use a drill to make holes for screws;
All wood surfaces must be sanded to ensure they are safe for hens and chicks;
Using screws and a screwdriver, connect all the cut out elements together into one structure. To achieve maximum density, you can use a clamp. It is worth paying attention to the fact that the back and front walls should be attached at an angle of 15 degrees;
Using hinges, attach the cover to the back of the side walls;
It is advisable to treat the finished structure with an antiseptic. It is strictly forbidden to use varnishes and paints.

The finished wooden feeder is spacious and comfortable. The feed is well protected from moisture and will be supplied automatically. The only drawback of this design is labor costs.

Also using wooden boards or pieces of thick plywood, you can easily make feeders in the form of a small trough. This design will be convenient for those who have a large number of chickens and a shelter from bad weather.

Required materials:

Pieces of boards or thick plywood;
Hammer;
Screws or nails;
Saw;
Simple pencil;
Paper;
Ruler.

Step-by-step manufacturing instructions:

First you need to make a drawing on paper, according to which the future structure will be made. In this case, it is necessary to accurately determine all the elements, their sizes and the places where the fasteners will be installed. This stage is the most critical, so you should avoid mistakes and inconsistencies;
The drawing is transferred to wood. The dimensions of the elements should be as follows: bottom - 15x100 cm, side walls - 8x100 cm, beam - 2x3x100 cm, end walls 15 cm wide and a height equal to the height of the long side walls + the thickness of the bottom. The most difficult stage in making such a feeder is cutting out the end walls;
Based on the drawn up drawing, it is necessary to cut out all the constituent elements. It is worth paying attention to the fact that the bottom should be quite thick and heavy so that the chickens cannot turn over the finished feeder. The height of the side walls should be comfortable for birds;
All cut out elements must be connected to each other so that there are no gaps left, as food can spill out through them. The finished structure does not require additional processing.

The main advantage of such a feeder is its durability and strength. In addition, it can be used for both dry and wet food. The only drawback is that the structure requires minimal maintenance.

Food and water are important for any living organism. Therefore, when breeding chickens, special attention should be paid to the quality of feeders. A properly selected element of maintenance allows you to increase productivity and take care of the health of birds, since pathogens can enter the chickens’ bodies through contaminated food and water.

A good feed device also saves the owner’s time and effort, which is mainly important when keeping a large number of animals. In addition, the thoughtful design of the feeder helps keep food out of unwanted mouths such as mice, rats and sparrows.

Requirements for chicken feeders

A glass jar feeder is not a very practical solution; the food may spill, chickens may knock over the jar, and you need to monitor the availability of food.

Like any element of maintenance, bird feeders must meet certain requirements.

Ensure rational use of feed. The structure must be made in such a way that chickens cannot climb into it, scatter food or spoil it with excrement. This can be achieved using various elements of the feeder (sides, turntables, nets, jumpers), which protect the bulk of the feed inside the device.
Optimal size and volume. The feeder must provide the entire population of birds with food. Moreover, its design should provide simultaneous access to food to all chickens, so that strong individuals do not drive away weak ones. Find out about cannibalism in chickens.
Ease of use. The device is easy to clean, food can be poured into it without any problems, and it is also convenient for birds.
Strength, stability, safety. The material of the feeder should deform as little as possible during use and be non-toxic to birds. The structure must be stable when in contact with chickens, and not tip over or fall on its side.
Fit for purpose. A feeder made of a specific material must be used for a specific type of feed.

To calculate the length of the tray, 10-15 cm is allotted for each adult, and 5 cm is enough for chickens. In a circular tray device, each bird receives 2.5 cm.

View

All feeders are classified according to the following criteria:

method of fastening;
type of food (wet, dry, grass) and feeding method;
size;
manufacturing material.

By type of fastening there are:

Floor-standing. The main requirement for the design is stability. By installing the feeder on the floor, birds can easily climb into it, which will lead to unproductive wastage of feed and sometimes the spread of infectious diseases. Read about diseases of laying hens.
Wall-mounted. They are highly stable due to wall mounting.
Hanging. They are hung at the level of the bird's back so that it can peck the food without scattering it. This type of feeder is difficult for rodents to get into. He will tell you how to get rid of rats in a chicken coop.

The size of the feeders must correspond to the number of birds, otherwise their feeding will be insufficient. Each type is designed for a certain amount of food, so it can be one large container or several small ones. The calculation for birds is carried out as follows:

10-15 cm of tray is required for one adult;
for chicken feeders the figure is halved;
with a circular design, 2.5 cm of tray is required per bird.

For stable and high productivity, all birds must have access to the feeder at the same time.

Depending on the material used to make the feeders, there are:

Wooden. The best option for dry food and...
Plastic and metal. Designed for wet food, as they are easier to clean than wooden ones.
Made of mesh or metal rods. Used when feeding green grass.
Combined. Allows different types of feed to be given to chickens at the same time.

Homemade iron bucket feeder

According to the feed supply method, there are three types of design:

Tray. Any flat container with sides that can be used to feed chickens is considered. The most budget option, which is suitable for chickens, but due to instability is poor for feeding adult birds.
Grooved. The design is complemented by a restrictive removable grille or turntable. Thanks to this, each bird has its own compartment with food, and they can also be used for different types of food at the same time. You can find out about feed for laying hens.
Bunkers. An ideal choice when feeding dry food, as it allows you to fill the daily amount of grain or feed. Feed flows into the tray as needed, and the closed design keeps food clean and dry.

When selecting feeders, it is necessary to take into account all factors affecting the productivity of chickens. Right choice will significantly save costs on the care and maintenance of birds in the future.

We make it ourselves from scrap materials with our own hands

Feeders for broilers and laying hens can be purchased ready-made, but to save money they can be easily made independently from available materials. As a material, you can use almost anything that is at hand (boards, boxes, pipes, plastic bottles, etc.). The main thing is that the material from which the feeder will be made is safe for the health of the birds. The main problem in production is mixing the feed. The best option is a universal feeder that is suitable for any type of food. If it is impossible to make such a container, you can make several separate ones for each type of food. However, when using several feeders at the same time, they take up a lot of space.

When making feeders yourself, at the final stage you should make sure that the design does not have sharp or protruding parts that could harm the birds during operation.

From a cutting board

To make this feeder you will need:

cutting board;
funnel (preferably plastic);
small plastic cup;
transparent rubber hose;
electric drill.

To begin with, you need to trace the outline of the wide part of the funnel as accurately as possible on the board. Next, many holes are drilled in the circled area at some distance from each other. Their number should be sufficient to allow food to pass through, but at the same time limit the amount of food it appears. The pre-prepared hose is then connected to the end of the funnel, and additional fasteners can be used if necessary. After this, a hole is made on the side of the plastic cup, the diameter of which is slightly larger than the diameter of the hose. The second end of the hose is placed in the hole of the cup. If the fastening density is insufficient, a sealant can be used. Next, the bell of the funnel is glued to the cutting board using sealant so that the outline of the funnel coincides with the drawn outline. After this, the funnel will be located on the bottom of the board and connected with a hose to the mug.

He will tell you how to make drinking bowls for chickens with your own hands.

Thanks to this system, the food will flow through the hose into the cup. However, care must be taken to ensure the stability of the board, as birds may land on it.

From a plastic bucket

An old plastic bucket makes a stable floor feeder

To make a bunker feeder from a bucket you will need:

plastic bucket;
fastening materials;
tool for creating holes (drill, knife);
special sectional bowl for animals.

To begin with, holes are made in the very bottom of the bucket through which the food will flow. After this, using screws, a sectional bowl is attached to the bottom, on the outside of the container. The bucket is turned over, food is poured into it and the lid is closed. When manufactured correctly, each hole opens into a separate section, where feed is supplied as needed. The advantages of such a feeder are automatic feed supply and ease of installation in or.

This type of feeder can be purchased ready-made, but it will be expensive. It can be considered automatic, since when it is used, participation in feeding chickens is minimal.

From plastic bottles

Such material can be found in most households. To make a feeder you need:

Take 2 bottles and cut the first one in half. In the lower part, at a distance from each other, cut holes, the diameter of which allows the bird to freely stick its head inside.
In the second bottle, cut off the bottom, turn it over and install the parts with holes inside so that the neck does not reach the bottom by a few centimeters. The grain is poured inside the bottle, after which the top part is closed.

This feeder is easy to carry, but in bad weather it must be covered indoors. A chicken feeder can be made using the same principle, only using a smaller bottle as a basis.

Two options for wooden feeders

Wood can be found in any yard, which is why many feeders are made from this material.

First option

These feeders are made of a hopper type, so they are suitable for owners who do not have the opportunity to frequently feed their birds. To make it you will need:

pieces of durable plywood or wood;
saw;
electric drill, set of drills;
screwdriver;
several loops;
sandpaper;
roulette;
pencil.

First you need to create a drawing, which will then be transferred to the tree. The standard parameters are:

bottom - 29x17 cm;
two side parts 40 cm high with a top edge of 24 cm and a bottom edge of 29 cm;
two rectangular panels for the front wall, 28x29 and 70x29 cm, respectively;
top cover - 26x29 cm;
back wall - 40x29 cm.

Metal feeder - strong and durable

After accurate measurements, all elements are carefully cut out. In the designated places, holes for screws are made using an electric drill. All elements should be sanded until smooth to protect the birds. After this, all parts are assembled into a single structure and fastened with screws. If necessary, you can use a clamp to increase the tightness of the seal. The front and rear walls must be attached at an angle of 15°. The lid is then secured to the back of the side walls using hinges. It is advisable to treat the finished product with an antiseptic. This feeder is comfortable and roomy. Apart from difficulties at the creation stage, it has no disadvantages.

When processing the feeder, it is strictly forbidden to use paints or varnishes.

Second option

This product is suitable if you have a large number of birds and a canopy in case of bad weather. The feeder is universal, durable and strong. Necessary materials for the manufacture of:

thick boards or plywood;
saw;
hammer;
screws or nails;
paper;
Ruler and pencil.

First, a clear drawing is made, the dimensions of all elements are calculated, and after that the measurements are transferred to the tree. Standard product parameters:

bottom - 15x100 cm;
2 side walls, 8x100 cm each;
1 beam – 2x3x100 cm (HxWxD);
small end walls 15 cm wide and with a height corresponding to the long side walls + the thickness of the bottom.

All elements are carefully cut in according to the drawing, processed with sandpaper and fastened together. It is advisable that there are no gaps left, as food can spill out through them.

One piece should be thick and heavy enough to prevent birds from knocking it over.

Two-story

This type is primarily used for dry feeding, although if necessary it can be used when feeding mash. Ideal for saving space, especially in small spaces. The structure is made of bars, screws and hinges. The first step is to measure and cut out all the elements of the future structure. In this feeder, the lower floor is the main one, its height is 25 cm, and its width is 26 cm. The length depends on the number of birds that will use the product. The end sides of the lower tier should be 8-10 cm higher than the wall. Next, special grooves are made into which the damper will later be placed. The second floor is made in the form of a small trough with a board height of 10 cm. It is installed on the ends of the lower floor and secured with hinges.

In addition to saving enormous space, such feeders are stable and birds cannot climb into them, which significantly saves feed.

From PVC pipes

The best option for farms with a large number of chickens. Manufacturing does not require much cost or effort, since PVC pipes are sold everywhere and have low price. There are many ways to make pipe feeders, but two are the most common.

With cutouts

You can make an excellent feeder from a plastic pipe by pre-cutting holes

For this option you will need:

2 PVC pipes, 40 and 60 cm in length;
2 plugs;
connecting elbow.

A long pipe is installed horizontally and is used for feeding. A short pipe is mounted vertically and is used to store and supply feed. First, holes with a diameter of 7 cm and with the same distance from each other are drawn on a large pipe. After this, holes are cut in the designated places. The hole can be made on one side or both. Then a plug is attached to one end of the horizontal pipe. On the other side, an elbow is installed, and a vertical pipe is placed in it. When installing, the finished feeder must be firmly secured in 2-3 places. After the feed is poured into the smaller tube, the end is closed with a second plug to keep out debris.

The design of the feeder is a bunker, so food can be added 1-2 times a day.

With tee

For the second version of the feeder you will need:

PVC pipes 70, 20, 10 cm long;
2 plugs;
tee with an angle of 45°.

A plug is placed on one side of the middle pipe. It will serve as the bottom of the product. On the other side, a tee is attached to the pipe so that the side elbow faces upward. A small pipe is installed in the side of the elbow, and the largest is placed in the remaining hole of the tee. As in the previous feeder, after filling the feed, the pipe must be closed with a plug.

From a canister

A low-cost and simple way to make a feeder. To create it you will need:

any plastic canister;
pipe 10-15 cm long
fastening materials

First, the canister must be thoroughly cleaned and then dried. After this, using a knife or other tool, cut about 5 holes on the side parts. Their diameter should be approximately 6-7 cm so that the bird’s head can easily fit into it. A hole is cut in the upper part of the canister, matching the diameter of the pipe. After this, a pipe is installed to fill the grain. Thanks to this design, birds will not climb inside. To protect the food in bad weather, you can make a lid to close the pipe.

From a CD container

If you don’t have a plastic bucket, then a CD container can be used as a handy tool for making a feeder.

Even such unusual material can be used to create a feeder. To make this you will need a long container, a large bowl and a knife. Before starting production, the container must be thoroughly cleaned and dried. After this, 3-4 2x2 cm holes are cut out on its walls near the rim. Next, the container is filled with food, a bowl is placed on top, after which the entire structure is turned over and installed in the required place. This feeder is not durable and stable, so it is designed for a small number of chickens.

Since cutting holes in the plastic may leave sharp corners that can injure birds, the finished product should be carefully checked and any irregularities should be corrected if found.

Automatic with timer

This system involves independently pouring food into the tray from the storage container. There are many types of automatic feeders. The most popular type is a wooden automatic feeder with a pedal. To make this type you will need:

wooden boards or thick plywood;
thin wooden beams;
screwdriver, drill, drill bits, saw;
fastening materials;
sandpaper;
paper, pencil and ruler.

To begin with, a drawing of the product is drawn with calculations of the parameters of all elements. The standard feeder has:

2 side walls 40 cm high with an upper edge of 26 cm and a lower edge of 29 cm. Additionally, triangles are cut out on them so that the lower part is wide and protruding.
2 rectangles for the front part - 28x29 cm and 7x29 cm.
Rectangle for the roof 26x29 cm.
Rectangle for the back wall 41x29 cm.

Cover for the tray and pedal according to the dimensions of the structure.
To begin with, the wooden beams are cut into 6 parts. The 2 longest pieces (the length is calculated based on the width of the pedal and the box) will serve as a mount for the pedal. 2 medium ones are needed for the lid above the tray. A pair of short ones will serve to connect the lifting mechanism. Next, all parts are cut out and processed with sandpaper. After this, the automatic feeder is assembled, all elements are fastened with screws. The back panel should be at an angle of about 15˚. The top cover is secured with two hinges. Next, you need to secure the pedal to the bottom of the structure. Thanks to this element, when pressed, the tray with food will open. Thus, the food will be completely protected, and the birds can open the box on their own by standing on the pedal.

It is advisable to treat the finished structure with an antiseptic, but varnishes or paints should not be used.

Specifics of homemade chicken feeders for chickens

Chicks require less feed than adults, so the feeder should be small

The main difference between chick feeders is their size. Since chicks need less feed, the dimensions of their food container are much smaller compared to the feeders of adult chickens. In addition, chicks are very active, so containers with food and water must be strong, stable and safe. Chickens eat a lot, which is difficult to regulate with a large number of chicks. That's why the best solution will make an automatic feeder that can independently add food throughout the day. Chickens, like adult birds, love to climb into containers with food, contaminate the food and throw it out. Because of this feature, it is advisable to use the most protected feeders.

Video

In the video we will see an example of a self-made pipe feeder.

conclusions

High-quality, practical feeders are the key to good poultry productivity, their health and rational use of feed.
If you are not able to feed the birds on time from built homemade feeders, it is best to equip them with automatic feeders (automated chicken feeders with a timer, which can be purchased from the manufacturer in bulk for large quantity heads).
These designs will allow you to regulate the amount of chicken food during the day.
Feeders can be purchased ready-made, however self-production in most cases saves a lot of money. They can be made from literally any available material.
Don't forget about the safety of birds. The material of the feeder, like the nest, should not be toxic for them, since chickens like to peck at everything. In addition, the product should not have nicks, roughness or other defects that could harm the birds.

Do you already have one or are you just planning to equip it? You just need to think about feeder, which will save both money and energy.

In addition, the bird will eat regularly. Having poured the food once, you will not need to worry about replenishing it.

Yes, and in the chicken coop it will be much cleaner, the bird will not trample the food into the ground, that is, all the food will go directly to its destination.

When choosing it you need to take into account quantity And age birds you have and the types of food you give them. You can easily make feeders yourself or buy them.

In this article We will tell you in detail about the types of such feeders, their manufacture and selection criteria when purchasing.

Types of feeders

Feeders for laying hens are divided into kinds according to the constituent materials, position in the chicken coop and the type of feed used (liquid or dry).

By components materials they are divided into those made from:

Trees;
Plastic;
Galvanized iron.

By location Feeders in the cage can be:

Hanging;
Floor-standing.

Type supplied feed, the following feeders are produced or manufactured:

Tray. These are containers in the form of a trough, the walls of which do not allow mash or other liquid feed to be thrown to the chickens. A tray feeder is best for chickens;
Grooved. These are feeders with an easily removable restrictive grid or turntable. They have separators that allow you to fill it with both dry and liquid (mash, porridge, etc.) food;
Bunker. It is a cylindrical vessel with a tray at the bottom. The grain is poured into the feeding tray as the chickens empty it.

Advice! For dry food, a bunker-type feeder (for example: a simple plastic bottle) is better suited, the main advantage of which is the complete automation of feeding.

Necessary Requirements

There are only three Requirements for chicken feeders:

All food must be used. That is, the feeder needs to be made such that the bird I could not I would like to jump and scatter food around the chicken coop. For this purpose they are made turntables, sides and other devices. Also required sustainability products;
The feeder should be easy to maintain, i.e. the process of filling it with food should not cause technical difficulties. The feeder should also be easy to clean and move without difficulty;
Size and the capacity of the feeder should depend on the number of chickens. Preferably so that the size of each compartment is approx. 10 cm for adult birds and chicks - 5 cm. In a circular feeder, such compartments can be about 3 cm. As a result, both strong and weak birds will be fed, and the quality of meat and eggs will improve.

Making a feeder with your own hands

So, if you are going to make a chicken feeder yourself, then below are three options its manufacture.

Option one: bottle feeder

It's popular and simplest bunker feeder option. To make it you need:

Find a “thick” plastic bottle with a handle on the side and some kind of container for the tray. Good fit menazhnitsa, sold for seedlings;
Having retreated 8 centimeters from the bottom, you need to cut holes - through them the bird will peck the grain;
Attach the menagerie, cut the handle and hang the bottle on the cage.

Option two: plywood feeder

Many people have on their farms sheets plywood. You can make a lot out of them comfortable bunker feeder for laying hens. For this:

From a suitable sheet you need to cut out three walls of the future feeder with a height of 1m and fasten them;
So that there are no obstacles to the feed plywood at the bottom it is nailed under a small angle(for granulated feed - in 25 degrees, for grain – in 15 degrees);
Next we make the front restrictive side (not less 6 centimeters) and side sides (at least 12 cm);
Using self-tapping screws, screw the front wall and install the feeder in the chicken coop.

Advice! After manufacturing, it is recommended to paint the feeder to facilitate further care of it.

Option three: pipe feeder

To make this version of a chicken feeder you will need to buy sewer PVC pipe( 1 meter length), stubs suitable for her tee.

Manufacturing process:

The pipe must be cut into three parts ( 70 cm, 10 cm And 20 cm).
For a part at 20 cm A plug is put on top and a tee on the bottom.
The 70-centimeter part of the pipe is “set” on top of the tee, the other is the same - closed with a plug.
Inserted into the tee on the side 10 cm piece of pipe.
The finished structure is attached to the chicken coop cage. The feeder is ready.

Advice! At night, it is advisable to close the opening of the feeder with a plug, this will keep the food clean.

Where to buy a chicken feeder?

In assortment specialized stores have many feeders made in Russia, Italy and China at reasonable prices.

You can also purchase simplest device from plastic in about 110 rubles, and a more durable feeder made of galvanized iron in about 5,900 rubles(Novital).

At the time of buying ready feeders are important consider:

Materials from which the feeder is made. They shouldn't highlight toxic compounds harmful to the health of both humans and birds should not be oxidized;
Strength. The product must withstand fairly strong blows from the beak and not be damaged;
Accessibility for treatment with disinfectants and washing. The feeder should be easy figure it out.

Following video demonstrates a clear example of making a chicken feeder from PVC pipe:

Feed is one of the key factors in raising chickens. This is where most of the funds go. To properly distribute food and not lose it just like that, farmers build feeders. Of course, factory products differ in their performance, but with some skills, you can make feeders with your own hands that will be no worse than purchased ones. We’ll look at what you need for this in this article.

Materials

As you understand, feeding devices come in several types and differ in different parameters. The first thing that distinguishes products is the materials from which they are made.

The most popular tree among farmers. This natural material is great for dry food such as grain, feed and various minerals. But it is best to avoid raw food - it will remain on the material, which in the future will lead to rapid spoilage of food.

The chicken diet must include mash. For this type of food, plastic products are ideal - they are easy to clean, which significantly increases savings.

Hopper feeders are made of metal. Most often, these are arched products, where the back wall is “blank” and the front side is covered with a mesh.

Feeding method

How convenient it is for farmers to feed poultry depends on this factor - it is much easier to do it once a day than to constantly replenish the supply:

Tray models perfectly serve as chicken feeders. Generally speaking, this is an ordinary container with sides that prevent food from spilling out. The elongated shape allows you to increase the number of birds feeding at a time.
The groove model has a special spinner and a demarcation grid. There may also be partitions inside - convenient if several types of food are used at once.
Automatic feeders, or bunkers, are very practical. You can pour dry food and grain into them. Standard size- daily food intake for chickens. At the bottom, the structure is equipped with a tray - when the bird eats, it is replenished without human intervention.

Nuances of feeders

The main task of the products is to use feed economically. To do this, first of all, various protective devices are installed, in the form of turntables, nets, sides and others. Otherwise, the bird will rake and throw food out of the feeder, which is in no way compatible with rational use.

Service - no less important factor. Since containers get dirty quickly, they need to be washed and cleaned quite often. To avoid difficulties with this, it is necessary to use suitable materials and design.

The volume of the feeder should be equal to required quantity one meal. At the same time, you also need to take into account the dimensions - so that all chickens have free access.

Options

We present to your attention some ideas for feeders that will turn out no worse than store-bought ones. They will be easy to use, which will significantly increase their value. At the same time, the food will not need to be replenished every time - it is enough to do it once a day.

The simplest product is considered to be a bottle hopper. To do this, you need to remove the bottom from a five-liter bottle so that 15-centimeter sides remain on it. We make a hole in it and fix it on plywood. The entire design can be slightly improved by adding one and a half liter and two-liter containers.

PVC pipes are also considered an excellent material for making feeders. For the horizontal option, you need to take a 150 mm pipe and put on the elbows on both sides - to fill the feed.

You need to make several windows in the sidewall through which the bird will feed. All that remains is to fix it on the wall. For the vertical version, we put on a tee with two elbows - but such a product is designed for a small number of chickens - take this nuance into account.

A homemade grass bunker is relatively easy to make, especially if you have the right tools. You need to select steel rods and weld and connect them using a welding machine. Then all that remains is to fix it on the wall. The proposed photos of chicken feeders will help you decide on the right one.

Photos of chicken feeders

home » Investments » Mesh feeders for grass for chickens. Do-it-yourself bunker feeder for chickens: how to make different designs. A simple option from a plastic bottle