Setup and testing technician job description. Setup and testing technician. I. General provisions
Qualification directory for positions of managers, specialists and other employees
Approved by Resolution of the Ministry of Labor of the Russian Federation of August 21, 1998 N 37
(as amended:
Resolutions of the Ministry of Labor of the Russian Federation dated January 21, 2000 N 7, dated August 4, 2000 N 57, dated April 20, 2001 N 35, dated May 31, 2002 N 38, dated June 20, 2002 N 44, dated July 28, 2003 N 59, dated November 12, 2003 N 75,
Orders of the Ministry of Health and Social Development of the Russian Federation dated July 25, 2005 N 461, dated November 7, 2006 N 749, dated September 17, 2007 N 605, dated April 29, 2008 N 200)
| Previous |
Section I. Industry-wide qualification characteristics positions of workers employed at enterprises, institutions and organizations
2. Specialist positions
Setup and testing technician
Job responsibilities. Under the guidance of a commissioning and testing engineer, performs commissioning work (testing) various types equipment and systems (electrical equipment, Technical equipment, ventilation, etc.). Establishes compliance with the technical characteristics of the installed equipment and installation work technical and design documentation, identifies defects in work and equipment, and ensures their elimination. Participates in the preparation of calendar schedules and programs for commissioning work, in the development of measures for occupational health, safety, industrial sanitation and fire protection during commissioning work, in the acceptance of equipment after tests performed installation organization. Connects devices, registers the necessary characteristics and parameters, and processes the results obtained. Participates in carrying out the necessary calculations, as well as in testing and adjusting equipment idle, under load and during comprehensive testing. Draws up acts in the forms established by current regulatory documents, indicating in them the volumes of commissioning work performed.
Must know: regulatory, methodological and other guidance materials for installation and commissioning work; organization of commissioning work; basic specifications, features of kinematic diagrams and designs of units and elements of systems and devices being adjusted and tested; methods for measuring parameters, characteristics and operating modes of equipment; rules for using measuring instruments and tools, devices; the procedure for inspecting equipment, methods for detecting its defects; rules for drawing up acts and other technical documentation; fundamentals of economics, scientific organization of labor and organization of production; basics of labor legislation; rules and regulations of labor protection, safety, industrial sanitation and fire protection.
Qualification requirements.
Installation and testing technician of category I: secondary vocational (technical) education and work experience as a technician of category II for at least 2 years.
Installation and testing technician category II: secondary vocational (technical) education and work experience as a technician or other positions filled by specialists with secondary vocational education, at least 2 years.
1. GENERAL OCCUPATIONAL SAFETY REQUIREMENTS
1.1. This Instruction provides basic labor protection requirements for an instrumentation and testing engineer.
1.2. The instrumentation and testing engineer must perform his duties in accordance with the requirements of these Instructions.
1.3. Workers may be exposed to the following hazardous and harmful production factors:
increased noise and vibration levels;
dangerous voltage level in an electrical circuit, the closure of which can occur through the human body;
increased contamination with vapors of harmful chemicals;
falling from height;
fire and explosion hazard;
thermal burns;
driving mechanisms and machines.
1.4. Persons who are at least 18 years old, have appropriate qualifications, have passed a medical examination, tested their knowledge of labor safety requirements by a commission in the prescribed manner, and have received permission to work independently are allowed to work as an engineer for commissioning and testing of instrumentation and control systems.
1.5. The instrumentation and testing engineer is provided with special clothing and safety footwear in accordance with current standards.
1.6. The commissioning and testing engineer for instrumentation and automation must have the appropriate electrical safety group, not lower than III.
1.7. An instrumentation and testing engineer needs to know and strictly comply with the requirements for labor protection, fire safety, and industrial sanitation.
1.8. The instrumentation and testing engineer notifies his immediate supervisor about any situation that threatens the life and health of people, about every accident that occurs at the workplace, about a deterioration in his health, including the manifestation of signs of an acute illness.
1.9. Instruments used for measurement, automatic control and regulation of parameters must comply with the class of fire and explosive zones, the group and category of explosive mixtures and the Fire Regulations in the Russian Federation.
1.10. Loading and unloading operations must be carried out in accordance with the requirements of GOST 12.3.009-76, GOST 12.3.020-80 and Labor Safety Rules during loading and unloading operations and placement of cargo.
1.11. Work with harmful and explosive substances must be carried out with the ventilation systems turned on, using personal protective equipment that ensures the safety of its work (dielectric gloves, dielectric mat, tools with insulating handles, portable grounding, posters, etc.).
1.12. The presence of unauthorized persons in the working space of the equipment during its adjustment or testing is not allowed.
1.13. The operation of instruments and equipment used to measure automatic control and regulation of parameters must be carried out in accordance with the technical documentation of the organization that developed the technological process.
1.14. The commissioning and testing engineer for instrumentation and automation must undergo labor protection training in the form of induction training, initial training in the workplace in the profession, including occupational safety issues and requirements job responsibilities by profession.
Induction training is carried out by an employee of the labor protection service or an employee replacing him with all those hired according to a program approved by the employer and agreed with trade union committee or other representative body of workers.
Initial briefing at the workplace is carried out by an official determined by order individually before the start production activities employee under the occupational safety program by profession.
1.15. An instrumentation and testing engineer must know:
Production instructions and labor protection instructions according to the approved list;
Block diagram of the instrumentation and automation system;
Purpose, devices, operating principles and rules technical operation instrumentation and automation;
Technical documentation for the operation of instrumentation and automation and current standards for its design;
Internal rules labor regulations enterprises;
Rules for the use of electrical protective equipment;
Rules safe work with tools and accessories;
First aid instructions, be able to provide first aid to victims.
1.16. Smoking and eating are allowed only in places specially designated for this purpose.
2. OCCUPATIONAL SAFETY REQUIREMENTS BEFORE STARTING WORK
2.1. Wear the protective clothing, safety shoes and personal protective equipment required by the relevant standards. Overalls must be fastened and must not have any loose ends. Shoes should not have steel nails or horseshoes.
2.2. Receive an assignment from the manager to carry out work on setting up and testing instrumentation and control equipment.
2.3. Prepare the protective equipment and devices necessary to perform the work.
2.4. Do not allow untrained or unauthorized persons to perform your work.
2.5. Check the lighting condition of the workplace.
2.6. Check the availability and serviceability of protective equipment, devices and tools used in the work.
2.7. All work on setting up and testing instrumentation and automation, depending on the type and nature of the work, must be issued with a work permit for the work. increased danger, by order or entry in the work log according to the list of works performed in the order of current operation.
2.8. When working on electrical equipment with voltage relief, you must:
ensure the necessary shutdowns (switchings) and take measures to prevent the supply of voltage to the place of work due to erroneous or spontaneous switching on of switching equipment;
check the presence of prohibiting posters on the manual drives and on the remote control keys of the switching equipment;
check the absence of voltage on live parts;
ensure the presence of warning and ordering posters, fencing if necessary workplace and remaining live parts.
2.9. If it is necessary to carry out any work on circuits or on relay protection equipment, electrical automation and telemechanics while the main equipment is turned on, measures must be taken to prevent its accidental shutdown.
2.10. Before starting any repair work on existing process equipment and pipelines, the instrumentation and automation engineer must coordinate this work with the operating personnel. Warning posters must be posted at shutdown locations.
2.11. Place tools, devices and materials in a convenient and safe place for use.
2.12. Check the serviceability of grounding, the presence and serviceability of fire-fighting equipment, the operation of ventilation units, and electrical equipment. All exposed and accessible moving parts of the equipment must be protected with secured guards.
3. OCCUPATIONAL SAFETY REQUIREMENTS DURING WORK
3.1. Work only in working clothing and safety shoes and use individual means protection.
3.2. When working around unguarded rotating parts, ensure that they are guarded. Do not turn on or stop, except in emergency cases, machines, machines, mechanisms on which work is not assigned.
3.3. Work in the presence and serviceability of fences, blocking and other devices that ensure labor safety, with sufficient lighting. For local lighting during repairs and inspections in explosive premises and outdoor installations, it is necessary to use explosion-proof flashlights with a voltage not exceeding 12 V. Turning on and off the flashlights must be done outside the explosive zone.
3.4. When using a portable electric lamp, check for protective mesh, the cord is in good condition, the voltage of the portable lamp is allowed no higher than 12 V.
3.5. Use only serviceable tools and protective equipment. Handle power tools with care, do not throw them, or allow them to fall.
3.6. Work in circuits of relay protection devices, electrical automation and telemechanics must be carried out in accordance with the executive circuits. Working without diagrams or from memory is prohibited.
3.7. Plumbing tools must have insulating handles.
without a stamp or with an expired stamp, or without a certificate of verification;
not meeting the established measurement accuracy;
damaged and in need of repair and verification.
3.9. Use proper factory-made voltage indicators.
3.10. When working with live equipment in damp or unheated rooms, wear dielectric galoshes or stand on a dielectric mat.
3.11. It is not allowed to operate automation equipment if it is malfunctioning. electrical networks power supply of devices and networks connecting primary devices with secondary ones.
3.12. All secondary windings of current and voltage instrument transformers must be permanently grounded.
3.13. It is prohibited to use process pipelines containing flammable and explosive liquids, as well as pipelines coated with insulation to protect against corrosion, as grounding conductors and grounding wiring.
3.14. When working in voltage transformer circuits with voltage supplied from an external source, it is necessary to remove the fuses on the high and low voltage side and disconnect the circuit breakers from the secondary windings.
3.15. It is prohibited to carry out work on panels or near the location of relay equipment that causes strong shaking of the relay equipment, threatening false operation of the relay.
3.16. It is prohibited to carry out work on checking and adjusting electrical automation and communications devices in the presence or possibility of a sudden appearance in production premises explosive gas, as well as in the production hazardous work for cleaning devices, replacing gaskets, seals, etc.
3.17. Carrying out hot work must be carried out with a permit and organizational and technical measures.
3.18. When working in explosive areas, ensure the use of tools that prevent the formation of sparks.
3.19. Explosion-proof automation equipment is allowed to be used in explosive premises, provided that the devices comply with the degree of danger of the given premises (premises class).
It is prohibited to use electrical equipment that is not marked for explosion protection in hazardous areas.
3.20. Instrumentation and control devices that do not have appropriate markings regarding the type and level of explosion protection are installed in rooms isolated from explosive atmospheres.
3.21. When working in hazardous areas, it is prohibited:
repair electrical equipment and networks under voltage without appropriate registration and carrying out organizational and technical measures;
operate electrical equipment in case of any damage (for example, faulty protective grounding, blocking, contact grounding, if the explosion protection of the equipment is violated);
operate explosion-proof electrical equipment with enclosure parts removed, incl. fastenings provided for by its design;
load electrical equipment, wires and cables beyond their rated parameters;
change the complete set of intrinsically safe devices, change the brand and increase the length of wires and cables if the resistance, capacitance and (or) inductance during this replacement exceed the maximum permissible values of these values for a given intrinsically safe circuit;
use the same cable for wiring intrinsically safe and conventional electrical circuits;
leave open the doors of rooms and vestibules separating explosive rooms from other explosive and non-explosive rooms;
turn on electrical installations without devices that disconnect the protected electrical circuit under abnormal conditions; replace protection (thermal and electromagnetic releases, fuses, residual current devices) of electrical equipment with other types of protection or protection with other nominal parameters, for which this electrical equipment is not designed;
leave electrical equipment in operation with a layer of oil and quartz sand below the specified height.
3.22. Do not allow strangers into the work site.
3.23. If any violations are detected, turn off the equipment and notify the supervisor.
4. OCCUPATIONAL SAFETY REQUIREMENTS IN EMERGENCIES
4.1. If an equipment breakdown occurs that threatens an accident at the workplace, stop its operation, as well as the supply of electricity, gas, water, raw materials, product, etc.; report on measures taken to the immediate supervisor (the person responsible for the safe operation of the equipment) and act in accordance with the instructions received.
4.2. In an emergency: notify people around you of the danger, report to your immediate supervisor about the incident and act in accordance with the emergency response plan.
4.3. In case of a chemical burn, wash the affected area immediately big amount running cold water from a tap, rubber hose or bucket for 15-20 minutes. If acid or alkali gets on the skin through clothing, you must first wash it off with water from the clothing, and then rinse the skin.
4.4. If splashes of alkali or vapors get into the eyes or mouth, rinse the affected areas with plenty of water and then with a solution of boric acid (0.5 teaspoon of acid per glass of water).
4.5. In the event of a fire, you must:
stop working;
turn off the equipment you are using;
Call the fire brigade, inform the work manager and begin extinguishing the fire using available means.
4.6. If there is a fire at electrical installations, use carbon dioxide and powder fire extinguishers.
4.7. If there are wounds, apply a bandage; if there is arterial bleeding, apply a tourniquet.
4.8. In case of injury, poisoning or sudden illness, the victim must be provided with first (pre-medical) aid and, if necessary, his delivery to a healthcare facility must be organized.
4.9. If acid gets on the floor, it should be neutralized (sprinkled with soda or quicklime) and only then cleaned with a shovel and washed off with water. Clothes drenched in acid should be washed with plenty of water, neutralized with a 2-3% soda solution and replaced.
4.10. If any malfunction is detected that disrupts normal operation, it must be stopped. Inform your immediate supervisor of any observed shortcomings.
4.11. In the event of an accident, it is necessary to provide assistance to the victim first aid, if necessary, call an ambulance, inform your immediate supervisor and keep the situation at the workplace unchanged until the investigation, unless it poses a threat to workers and does not lead to an accident.
5. OCCUPATIONAL SAFETY REQUIREMENTS AFTER WORK COMPLETION
5.1. Remove temporary barriers and remove warning and prohibition posters. The place of work should be cleared of all equipment, tools, and accessories that were delivered for the work.
5.2. Organize your work area, tools and equipment.
5.3. Take off protective clothing, put away personal protective equipment, protective clothing in the designated place.
5.4. Wash your face and hands with warm water and soap or take a shower.
5.5. Inform the work manager about all malfunctions noticed during work and the measures taken to eliminate them.
0.1. The document comes into force from the moment of approval.
0.2. Document developer: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _.
0.3. The document has been approved: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _.
0.4. Periodic verification of this document is carried out at intervals not exceeding 3 years.
1. General Provisions
1.1. The position "Commissioning and testing technician" belongs to the "Specialists" category.
1.2. Qualification requirements- commissioning and testing technician category I: basic or incomplete higher education relevant field of study (bachelor or junior specialist). Work experience as a commissioning and testing technician of category II - at least 1 year. Adjustment and testing technician category II: basic or incomplete higher education in the relevant field of training (bachelor or junior specialist): for a bachelor - no work experience requirements, for a junior specialist - work experience in the profession of adjustment and testing technician - at least 2 years . Setup and testing technician: incomplete higher education in the relevant field of training (junior specialist) with no work experience requirements.
1.3. Knows and applies in practice:
- methodological, regulatory and other guidance materials for installation and commissioning work;
- organization of commissioning work;
- main technical characteristics, features of kinematic diagrams and designs of units and elements of adjusted and tested circuits and devices;
- methods for measuring parameters, characteristics and operating modes of equipment;
- rules for using measuring instruments and tools, devices;
- the procedure for inspecting equipment, methods for identifying defects;
- rules for drawing up acts and other technical documentation;
- basics of economics, scientific organization labor and production organization;
- basics of labor legislation.
1.4. An adjustment and testing technician is appointed to the position and dismissed from the position by order of the organization (enterprise/institution).
1.5. The commissioning and testing technician reports directly to _ _ _ _ _ _ _ _ _ _ .
1.6. The commissioning and testing technician supervises the work of _ _ _ _ _ _ _ _ _ _ .
1.7. During absence, the setup and testing technician is replaced by a person appointed in accordance with the established procedure, who acquires the appropriate rights and is responsible for the proper performance of the duties assigned to him.
2. Characteristics of work, tasks and job responsibilities
2.1. Under the guidance of a commissioning and testing engineer, performs commissioning (testing) of various types of equipment and systems (electrical equipment, technical equipment, ventilation, etc.).
2.2. Establishes compliance of the technical characteristics of the installed equipment and installation work with technical and project documentation, detects defects in work and equipment, ensures their elimination.
2.3. Participates in the preparation of calendar schedules and programs for commissioning work, in the development of labor protection and fire protection measures during the commissioning process, in the acceptance of equipment after tests performed by the installation organization.
2.4. Connects devices, registers the necessary characteristics and parameters, and processes the results obtained.
2.5. Participates in carrying out the necessary calculations, as well as in testing and adjusting equipment idle, under load and in complex tests.
2.6. Draws up acts in accordance with the forms established by current regulatory documents, indicating in them the volumes of commissioning work performed.
2.7. Knows, understands and applies current regulations relating to his activities.
2.8. Knows and complies with the requirements of regulations on labor protection and environment, complies with the standards, methods and techniques of safe work performance.
3. Rights
3.1. The commissioning and testing technician has the right to take action to prevent and correct any irregularities or non-conformities.
3.2. The setup and testing technician has the right to receive all social guarantees provided for by law.
3.3. The commissioning and testing technician has the right to demand assistance in the performance of his duties and rights.
3.4. The setup and testing technician has the right to demand the creation of organizational and technical conditions necessary for the performance of official duties and the provision necessary equipment and inventory.
3.5. The commissioning and testing technician has the right to familiarize himself with draft documents relating to his activities.
3.6. The commissioning and testing technician has the right to request and receive documents, materials and information necessary to perform his job duties and management orders.
3.7. The commissioning and testing technician has the right to improve his professional qualifications.
3.8. The commissioning and testing technician has the right to report all violations and inconsistencies identified in the course of his activities and make proposals for their elimination.
3.9. The setup and testing technician has the right to familiarize himself with the documents defining the rights and responsibilities of the position held, and the criteria for assessing the quality of performance of job duties.
4. Responsibility
4.1. The setup and testing technician is responsible for failure to perform or untimely fulfillment of the duties assigned by this job description and (or) failure to use the granted rights.
4.2. The setup and testing technician is responsible for failure to comply with internal labor regulations, labor protection, safety regulations, industrial sanitation and fire protection.
4.3. The commissioning and testing technician is responsible for disclosing information about the organization (enterprise/institution) related to trade secrets.
4.4. The setup and testing technician is responsible for failure to comply or improper fulfillment of the requirements of internal regulatory documents of the organization (enterprise/institution) and legal orders of management.
4.5. The commissioning and testing technician is responsible for offenses committed in the course of his activities, within the limits established by the current administrative, criminal and civil legislation.
4.6. The commissioning and testing technician is responsible for any damage caused material damage organization (enterprise/institution) within the limits established by current administrative, criminal and civil legislation.
4.7. The commissioning and testing technician is responsible for the unlawful use of the granted official authority, as well as the use of it for personal gain.
Name of company
OFFICIAL
INSTRUCTION No.__
Setup and testing technician
Real job description developed in accordance with the functional structure of the organization and the provisions of the Labor legislation of the Russian Federation.
1.1. Setup and Test Technician is classified as
specialists.
1.2. For the position:
Installation and testing equipment category I - a person with an average
professional (technical) education and work experience in the position
Installation and testing equipment of category II - a person with
secondary vocational (technical) education and work experience in
technician positions or in other positions filled by specialists with
secondary vocational education, at least 2 years;
Adjustment and testing equipment is assigned to a person with an average
vocational (technical) education, without requirements for
work experience.
1.3. Appointment to the position of setup and testing technician and
exemption from it is carried out by order of the head of the enterprise according to
representation ________________________________________________________________.
1.4. The commissioning and testing technician must know:
Regulatory, methodological and other guidance materials on
carrying out installation and commissioning work;
Organization of commissioning works;
Main technical characteristics, kinematic features
diagrams and designs of units and elements of systems being adjusted and tested and
devices;
Methods for measuring parameters, characteristics and data modes
equipment operation;
Rules for the use of measuring instruments and tools,
devices;
The procedure for inspecting equipment, methods for detecting its defects;
Rules for drawing up acts and other technical documentation;
Fundamentals of economics, scientific organization of labor and organization
production;
Fundamentals of labor legislation of the Russian Federation;
Rules and regulations, safety precautions,
industrial sanitation and fire protection;
Rules and methods of providing pre-medical care medical care.
1.5. The commissioning and testing technician reports directly to
________________________________________________________________________.
(commissioning and testing engineer, other official)
1.6. During the absence of the adjustment and testing technician (vacation,
illness, business trip, etc.) his duties are performed by a person appointed
according to established order. This person acquires the corresponding rights and
bears responsibility for the proper execution of the duties assigned to him
responsibilities.
1.7. ______________________________________________________________.
2. Job responsibilities
Commissioning and testing technician:
2.1. Under the guidance of a commissioning and testing engineer, performs
commissioning (testing) of various types of equipment and
systems (electrical equipment, technical equipment, ventilation and
etc.), establishes compliance with technical characteristics
installed equipment and installation work, technical and design
documentation, identifies defects in work and equipment, ensures them
elimination.
2.2. Participates in the preparation of calendar schedules and programs
performing commissioning work, developing security measures
labor, safety, industrial sanitation and fire safety
protection during commissioning and acceptance of equipment after
tests performed by the installation organization.
2.3. Connects devices, registers the necessary characteristics and
parameters, processes the results obtained.
2.4. Participates in carrying out the necessary calculations, as well as in
testing and adjustment of equipment idle, under load and at
complex equipment.
2.5. Draws up acts in the forms established by the current
regulatory documents, indicating in them the volumes of completed
commissioning works.
The adjustment and testing technician has the right to:
3.1. Get acquainted with the draft decisions of the enterprise management,
relating to his activities.
3.2. Submit proposals for management's consideration
improvement of work related to the responsibilities provided for
this instruction.
3.3. Notify your immediate supervisor of any
identified during the performance of their official duties
shortcomings in the production activities of the enterprise (its structural
divisions) and make proposals for their elimination.
manager from heads of departments of the enterprise and specialists
information and documents necessary to perform their duties
responsibilities.
3.5. Involve specialists from all (separate) structural
units to solve the tasks assigned to it (if provided for
provisions on structural divisions, if not - with permission
manuals).
3.6. Require the management of the enterprise to provide assistance in
performance of his official duties and rights.
3.7. ______________________________________________________________.
4. Responsibility
The commissioning and testing technician is responsible for:
4.1. For improper performance or failure to fulfill their duties
duties provided for in this job description, in
limits defined labor legislation Russian Federation.
4.2. For offenses committed in the course of exercising their
activities - within the limits determined by administrative, criminal and
civil legislation of the Russian Federation.
4.3. For causing material damage - within the limits specified
labor and civil legislation of the Russian Federation.
4.4. ______________________________________________________________.
I have read the Job Description:
____________________________________________________________________________
(Last name of I.O., signature of the employee assigned to this position)
____________________________________________________________________________
(Last name of I.O., signature of the employee assigned to this position)
____________________________________________________________________________
(Last name of I.O., signature of the employee assigned to this position)
____________________________________________________________________________
(Last name of I.O., signature of the employee assigned to this position)
An adjustment and testing engineer is classified as a specialist.
Rules and regulations of labor protection, safety, production. Occupational safety during testing (measurements) selected necessary instructions and technical literature, selected for joint production of installation and commissioning work. Safety rules for measurements and tests.
Job description of a technician. Setup and testing technician
security. An adjustment and testing engineer is classified as a specialist. 1.2.
Engineer. rules and regulations of labor protection and fire safety. 1.6. Job description for commissioning test engineer. Job responsibilities Ensuring compliance with labor protection requirements in accordance with.
Instructions for labor protection during various types of work,
cross-industry instructions and safety instructions for.
installation, adjustment, repair work, testing, etc. Occupational safety during testing (measurements). selected
necessary instructions and technical literature, selected in.
joint implementation of installation and commissioning work.
Safety rules for measurements and tests.
Adjustment and testing technician - Job description for adjustment and testing technician. Job descriptions - HR LibraryYou can download the job description of a commissioning and testing technician for free. Job responsibilities of a setup and testing technician. I approve_______________________________________ (Last name, initials) (name of the organization, its ________________________________ organizational - legal form) (director; other person authorized to approve the job description)0. JOB DESCRIPTION OF SETTING AND TESTING TECHNICIAN - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - (name of institution)0. I. General provisions 1.
This job description establishes the rights, responsibilities and job responsibilities of the setup and testing technician ___________________________________________________ (hereinafter referred to as the “enterprise”). Name of the institution 1. The adjustment and testing technician belongs to the category of specialists. 1. A person appointed to the position: - installation and testing technician of category I must have a secondary vocational (technical) education and work experience as a technician of category II for at least 2 years; - installation and testing equipment of category II must have a secondary vocational (technical) education and work experience as a technician or in other positions filled by specialists with secondary vocational education for at least 2 years; - setup and testing technicians must have a secondary vocational (technical) education, without any work experience requirements. 1. Appointment to the position of adjustment and testing technician and dismissal from it is made on the basis of an order from the head of the enterprise upon the recommendation of _____________________________________________________. 1.
The setup and testing technician reports directly to _____________________________. 1. If the setup and testing technician is absent, then his duties are temporarily performed by a person appointed in the prescribed manner, who bears full responsibility for the proper performance of his official duties. 1. The setup and testing technician must know: - rules for using measuring instruments and tools, devices; - organization of commissioning work; - main technical characteristics, features of kinematic diagrams and designs of units and elements of systems and devices being adjusted and tested; - methods for measuring parameters, characteristics and operating modes of equipment; - the procedure for inspecting equipment, methods for detecting its defects; - rules for drawing up acts and other technical documentation; - rules and regulations of labor protection, safety precautions, industrial sanitation and fire protection; - rules and methods of providing pre-medical care; - fundamentals of economics, scientific organization of labor and organization of production, labor legislation of the Russian Federation; - regulatory, methodological and other guidance materials for installation and commissioning work; II. Job responsibilities The setup and testing technician performs the following job responsibilities: 2. Connecting devices, recording the necessary characteristics and parameters, processing the results obtained. 2. Drawing up reports in the forms established by current regulatory documents, indicating in them the volumes of commissioning work performed. 2.
Carrying out, under the guidance of a commissioning and testing engineer, commissioning work (testing) of various types of equipment and systems (electrical equipment, technical equipment, ventilation, etc. Participation in the preparation of schedules and programs for commissioning work, in the development of labor protection, safety, production measures sanitation and fire protection during commissioning, in the acceptance of equipment after tests performed by the installation organization 2. Participation in carrying out the necessary calculations, as well as in testing and adjusting equipment idle, under load and with complex equipment.
III. Rights The setup and testing technician has the right: 3. To contact management: - with demands for assistance in the performance of his official duties and rights; - with proposals for improving work related to the responsibilities provided for in these instructions; - with reports of all shortcomings in the production activities of the enterprise (its structural divisions) identified during the performance of their official duties and to make proposals for their elimination. 3.
Request personally or on behalf of your immediate supervisor from heads of departments of the enterprise and specialists information and documents necessary to perform their job duties. 3. Involve specialists from all (individual) structural units in solving the tasks assigned to it (if this is provided for by the regulations on structural units, if not, with the permission of management). 3. Get acquainted with the draft decisions of the enterprise management concerning its activities. IV. Responsibilities The commissioning and testing technician is responsible for: 4.
In case of causing material damage within the limits determined by the civil and labor legislation of the Russian Federation. 4. In case of commission of offenses in the course of carrying out their activities within the limits determined by the criminal, administrative and civil legislation of the Russian Federation. 4. In case of improper performance or failure to fulfill one’s official duties, which are provided for in this job description, within the limits determined by the labor legislation of the Russian Federation. Supervisor structural unit: _____________ __________________ (signature) (last name, initials) 0. I have read the instructions and received one copy: _____________ __________________ (signature) (last name, initials) 0.
